|
Parking
Sensor System à PS-01 |
|||||||||
|
This is a basic parking sensor system consists
of 2 ultrasonic sensors, digital control box and a buzzer. This system can detect the distance between
the car and the back obstruction by the ultrasonic sensors installed at the
rear bumper of the car with steps sounds.
Driver can tell the backing distance with the changing alarm sounds. |
|||||||||
|
|
|||||||||
|
Main Features |
|
||||||||
|
·
Bi-Bi alarm ·
Hidden
installation ·
2 Insert-in or
stick-on sensors |
|||||||||
|
|
|||||||||
|
Alarm Mode |
|
||||||||
|
Stage |
Distance |
Awareness |
Alarm Sound |
||||||
|
1 |
1.5 ~ 1.0M |
Safe Mode |
Bi…… Bi…… Bi…… Bi |
||||||
|
2 |
1.0 ~ 0.5M |
Alert Mode |
Bi … Bi … Bi … Bi … Bi |
||||||
|
3 |
0.4 ~ 0.0M |
Dangerous Mode |
Biiiiiiiiiii…….. |
||||||
|
|
|||||||||
|
Detecting Range |
|
||||||||
|
|
|||||||||
|
|
|||||||||
|
Connection Diagram |
|
||||||||
|
|
|||||||||
|
|
|
|
|
||||||
|
Technical Specifications |
|
||||||||
|
·
Rated Voltage:
12V DC ·
Operating ·
Rated Current:
20mA ~ 100mA ·
Detecting
Range: 0.3 ~ 1.5M ·
Ultrasonic
Frequency: 400KHz ·
Control Working
Temperature: -30 ~ +70°C |
|||||||||
|
|
|||||||||
|
Installation Diagram |
|
||||||||
|
Be sure no other parts of
the vehicle falls into the detecting range of sensors so as give a false
detection. |
|||||||||
|
|
|||||||||
|
Suggested positions to
install the sensors
|
|||||||||
|
|
|||||||||
|
Install the insert-in
sensors
|
|||||||||
|
|
|||||||||
|
Note: 1. The 3M double paster could not be used repeatedly;
the position to stick on the buzzer or sensor should be clean. The effect will become perfect in 48 hours. 2. Sensors’ wire should be well protected from damage. 3. Holes need to be drilled in the bumper to install
the insert-in type sensors. 4. Adjust the direction of the sensors to avoid false
detection. For round sensors, no need
to adjust the direction. |
|||||||||
|
|
|||||||||
|
Installation and test |
|
||||||||
|
1. After the installation of sensors, tune the
direction to the correct; arrange the wire in good order. 2. Connect the power supply of digital control box and
reverse light according to figures 3. Connect the horn with the digital control box (at
this moment no need to put the horn at the driver’s room since the purpose of
connection is to test it), don’t connect the sensors. 4. Put the car into back gear or brake the car, the
system will be in test status. Test: a) If there is no sounds, please check whether the
wire is connected correctly, whether the voltage is higher than 10V, whether
the plug of horn is connected well; b)
If there appear long sound, please switch the power off and then enter
into the back gear again, if the problems could not be removed, the control
unit could be decided to be failed.
The whole system should be replaced. 5.
Connect one of
the sensor into the corresponding outlet in the control unit, have someone to
stand 1.0M in front the sensor, if the detection is correct, disconnect this
sensor and test other one; After all
the sensors are tested ok, connect all sensors to the control unit. Test: a) When test
some sensor, if the horn sends long sound, please check if some parts of the
car or some unwanted object fall into the detecting range, if the sensor is near to some strong
interference sources (such as exhaust pipe, other wires). b) If the alarm sound is ”Bi.Bi“ but there is nothing in front of the sensor, The sensor might be detect ground, please
check the position and direction of the sensor. Or, the sensor might be detect
some parts of the car. C) If the problem still couldn’t be removed,
the whole system should be replaced. Note: a) Please
connect the sensors with the corresponding outlets in the control unit. B) For the concerning of safety, the horn
will only send “Bi…..” sound when detect something in the distance of 0.0 to
0.4M which is pre-designed. |
|||||||||
|
|
|||||||||
|
Remarks |
|
||||||||
|
1. When install the system, the car engine should be powered off. 2. The performance maybe affected in the following situation: Heavy rain; The gravel road, bumpy road; sloping road and bush; Very hot, cold or moist weather, the sensor is covered by snow, ice, mud… etc. 3. Other ultrasonic or electric wave, the instance of DC/AC switch or 24/12V switch maybe affect the performance of the system 4. The sensors should not be installed too tightly or too close. 5. The metal bumper maybe affect the performance of the system 6. Don’t locate the control unit near to other interference sources such as exhaust pip ot other wires. 7.
Test the system to make sure it works properly
before using. 8.
This system only acts as a kind if reminding
aid, in case of any accident, the manufacturer or distributor is not
responsible for the consequence. 9.
Objects maybe cause failure detection
|
|||||||||
